IEI Technology IMBA-9454B User Manual Download Page 101

Page: 101 / 192

IMBA-9454B ATX Motherboard

Page 85

interrupt if block mode is not used. Block mode allows transfers of up to 64 KB

per interrupt.

PIO Mode

: Indicates the PIO mode of the installed device.

DMA Mode

: Adjust the DMA mode options.

S.M.A.R.T.

: Indicates whether or not the Self-Monitoring Analysis and

Reporting Technology protocol is supported.

32Bit Data Transfer

: Enables 32-bit data transfer.

Type [Auto]

Use the Type BIOS option to select the type of device the AMIBIOS attempts to boot from

after the Power-On Self-Test (POST) is complete.

Not Installed

BIOS is prevented from searching for an IDE disk

drive on the specified channel.

Auto D

EFAULT

The BIOS auto detects the IDE disk drive type

attached to the specified channel. This setting should

be used if an IDE hard disk drive is attached to the

specified channel.

CD/DVD

The CD/DVD option specifies that an IDE CD-ROM

drive is attached to the specified IDE channel. The

BIOS does not attempt to search for other types of

IDE disk drives on the specified channel.

ARMD

This option specifies an ATAPI Removable Media

Device. These include, but are not limited to:

ZIP

LS-120

LBA/Large Mode [Auto]

Use the LBA/Large Mode option to disable or enable BIOS to auto detects LBA (Logical

Block Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the

maximum drive capacity is 137 GB.

Summary of Contents for IMBA-9454B

































































































































































































Search results

Summary of Contents for IMBA-9454B

Reviews:

Related manuals for IMBA-9454B

Brands by name

Popular brands

IEI Technology IMBA-9454B, User Manual

Search results

Summary of Contents for IMBA-9454B

Reviews:

Related manuals for IMBA-9454B

Brands by name

Popular brands