IEI Technology AFL-15A-N270 User Manual Download Page 85

Page: 85 / 158

AFOLUX AFL-15A-N270 Panel PC

Page 85

6.3.4 Hardware Health Configuration

The

Hardware Health Configuration

menu (

BIOS Menu 7

) shows the operating

temperature, fan speeds and system voltages.

BIOS Menu 7: Hardware Health Configuration

CPU FAN Mode Setting [Automatic mode]

Use the

CPU FAN Mode Setting

option to configure the second fan.

Full On Mode

Fan is on all the time

Automatic mode

EFAULT

Fan is off when the temperature is low

enough. Parameters must be set by the

user.

PWM Manual mode

Pulse width modulation set manually

When the

CPU FAN Mode Setting

option is in the

Automatic Mode

, the following

parameters can be set.

CPU Temp. Limit of OFF

Summary of Contents for AFL-15A-N270































































































































































Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands

IEI Technology AFL-15A-N270, User Manual

Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands