IEI Technology AFL-15A-N270 User Manual Download Page 59

Page: 59 / 158

AFOLUX AFL-15A-N270 Panel PC

Page 59

4.11 Bottom Panel Connectors

4.11.1 LAN Connection

There are two external RJ-45 LAN connectors. The RJ-45 connector enables connection

to an external network. To connect a LAN cable with an RJ-45 connector, please follow

the instructions below.

Step 1:

Locate the RJ-45 connectors

on the bottom panel of the AFOLUX

AFL-15A-N270 Series.

Step 2:

Align the connectors.

Align the RJ-45 connector on the LAN cable with one of

the RJ-45 connectors on the bottom panel of the AFOLUX AFL-15A-N270

Series. See

Figure 4-19

Figure 4-19: LAN Connection

Step 3:

Insert the LAN cable RJ-45 connector.

Once aligned, gently insert the LAN

cable RJ-45 connector into the onboard RJ-45 connector.

Step 0:

Summary of Contents for AFL-15A-N270































































































































































Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands

IEI Technology AFL-15A-N270, User Manual

Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands