IEI Technology AFL-15A-N270 User Manual Download Page 28

Page: 28 / 158

AFOLUX AFL-15A-N270 Panel PC

Page 28

Figure 2-8: Audio Jack

2.7.2 Stereo Speakers

Two internal 1.5 W stereo speakers on the sides of the AFL-15A-N270 are interfaced to

the system through a Philips TDA1517p integrated class-B dual output amplifier.

Figure 2-9: Stereo Speakers

2.8 System Power

2.8.1 Power Mode

The system can be run in the AT power mode or the ATX power mode. Both these power

modes are described below.

2.8.1.1 ATX Power Mode (Default)

With the ATX mode selected, the AFOLUX AFL-15A-N270 panel PC goes in a standby

mode when it is turned off. The panel PC can be easily turned on via network or a power

switch in standby mode. Remote power control is perfect for advertising applications

Summary of Contents for AFL-15A-N270































































































































































Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands

IEI Technology AFL-15A-N270, User Manual

Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands