Icom IC-M801E, Instruction Manual

Page: 23 / 80

15
6
DSC PREPARATION
6
■
Position and time programming
q
While pushing and holding [MODE
SET
] push
[POWER] to enter initial set mode.
• Turn the power OFF in advance.
w
Rotate [GRP] to select the “GPS DISPLAY” then
rotate [CH] to select the desired position indication
type from simple and detail.
e
Rotate [GRP] to select the “OFFSET TIME” then
rotate [CH] to set the time difference between local
and the UTC times within –12 to +12 hours in
10 minute steps.
r
Turn the power OFF once, then ON again to exit
quick set mode.
✔
When a position and the UTC time data
(NMEA0183 ver. 3.01 format) is applied to [GPS],
the following steps are not necessary.
t
Push [DSC] to select DSC watch mode.
y
Push [MODE
SET
] to enter the DSC menu.
• DSC menu is displayed as below.
u
Rotate [CH] to select “ Position ,” then push
[ENT].
i
Enter your position and the UTC time via the key-
pad, then push [ENT].
• Push [3
SCAN
] for the ‘East,’ [9] for the ‘West,’ [6
RF
-
G
]
for the ‘North’ and [7] for the ‘South’ setting.
• Rotate [CH] to move the cursor.
o
Push [ENT] to program the position and time.
• Return to the “ DSC MENU ” indication as in step
u
.
!0
Push [MODE
SET
] to exit the DSC menu.
• Rotate [CH] to select “ Exit ” then push [ENT] also
exits set mode.
• “ MNL ” appears instead of “ GPS .”
* * * * * * * P o s i t i o n * * * * * * *
- - - P o s i t i o n & t i m e - - - -
L a t i t u d e
L o n g i t u d e
U T C
3 4 3 4 . 3 4 3 N
1 3 5 3 4 . 3 4 3 E
1 2 : 3 4
O K N u l l
* * * * * * * D S C M E N U * * * * * * *
- - - - - - - - S e l e c t - - - - - - - -
P o s i t i o n
I n d i v i d u a l
G r o u p
P o s i t i o n R E Q
D i s t r e s s
D i s t r e s s R L Y
Ç
O K S E L
* * * S E T M O D E * * *
I T E M S E L
* * * S E T M O D E * * *
S I M P L E
D E T A I L
ÇÇ
I T E M S E L
[POWER] [MODE
SET
]
When no position and the UTC
(Universal Time Coordi-
nated)
time data in NMEA0183 ver. 3.01 format, such
as from a GPS receiver, etc., is applied to [GPS] con-
nector, your position and the UTC time should be input
for DSC operation.
IMPORTANT!
Manually programmed position and time data will be
held for 23.5 hours only, and “
? ” symbol is displayed
for all digits instead of the programmed data after 4
hours from programming.
They are never renewed during the voyage when
the position is set manually.
F 1 B
G P S
1 2 . 3 4 5 . 0
E x i t
S P
3 4 3 4 . 0 0 0 N
1 3 5 3 4 . 0 0 0 E
1 2 : 3 4
F 1 B
G P S
1 2 . 3 4 5 . 0
E x i t
S P
L a t 3 4 3 4 ' N
L o n 1 3 5 3 4 ' E
1 2 : 3 4
• Simple position indication • Detail position indication
M M S I 1 2 3 4 5 6 7 8 9 M M S I 1 2 3 4 5 6 7 8 9
IC-M801E_0.qxd 05.12.2 16:32 Page 15