icetro IM-0350-AC User Manual Download Page 41

Page: 41 / 44

9. Type of Product Error

Type of

Error

Display

Cause

What to DO

Release

Action

Front Indicator

Lamp

FND

Module
(Option

Full Bin

The bin is filled with ice.

Use of ice

Automatically
release when the
bin is emptied.

Stop

Water

Supply

Trouble

Er15

Water for making ice is not
supplied within the required
time. (Maximum 5 minutes or
less)

Check water

supply

connection

Reconnect power
after resolving water
supply problem.

Stop

Water

Level

Sensor

Trouble

Er16

It flickers when the water
level sensor (high/low level)
detects the water level as
the ice maker enters harvest
mode after making ice.

- Check
water supply
connection
- Clean/
replace
water level
sensor

Replace water
level sensor and
reconnect power
after resolving water
supply problem.

Stop

Trouble

in Ice

Making

Er01

When the outlet temperature
of the evaporator reaches
0℃ 30 minutes after the ice
making started.

Check cooling

unit

(Inquire Service

Center)

Reconnect power
after resolving
cooling problem.

Stop

Poor Ice

Making

Er03

When the outlet temperature
of the evaporator reaches
exceeds -5℃ 30 minutes
after the ice making started.

Check cooling

unit

(Inquire Service

Center)

Reconnect power
after resolving
cooling problem.

Run

Ice

Making

Delay

Er11

It flickers when the maximum
ice-making time (65 minutes)
is exceeded.

Check cooling

unit

(Inquire Service

Center)

- Clean ice
thickness sensor
- Reconnect
power after
resolving
cooling problem

Stop

consecutive

Times)

Ice

Harvest

Delay

Er12

It flickers when the maximum
harvest time (5 minutes) is
exceeded.

Check cooling

unit

(Inquire Service

Center)

- Clean/inspect
water curtain
and right magnet
detection unit
- Reconnect
power after
resolving
cooling problem

Stop

consecutive

Times)

High

Pressure

Detection

Er13

The water does not cool
down the gas (HIGH
PRESSURE S/W
is open).

Check water

supply line of

the cooling

unit

(Inquire

Service Center

when there is

a problem)

Reconnect power
after resolving the
cooling water
supply problem.

Stop

High

Pressure

Detection

Consecutive

Times)

Er14

Excessive

Cooling

Water

Supply

Er17

The water valve on the
cooling
unit (condenser) is
malfuncioning.

Run

Drainage

error

Er18

The sump water does not
drain.

Check drain valve

and drain line.

Check water level

sensor.

Reconnect power

after resolving

cooling problem.

Stop

Summary of Contents for IM-0350-AC













































Search results

Summary of Contents for IM-0350-AC

Reviews:

Related manuals for IM-0350-AC

Brands by name

Popular brands

icetro IM-0350-AC, User Manual

Search results

Summary of Contents for IM-0350-AC

Reviews:

Related manuals for IM-0350-AC

Brands by name

Popular brands