background image

20

We Think of Customer Satisfactio

n

Suitable installation condition and place

⊙ The product must be installed indoors.

◆ The outlet of the drain hose has to face downward
    to enable smooth draining.
◆ The product must not be installed outside.

⊙ Be sure to install the product in clean places.

◆ Ice will be used for food or human consumption.
    Thus, the installation site must be clean and hygienic.

⊙ In a place inaccessible to children.

◆ Please pay proper attention to the safety 
    of children; make sure that no one plays 
    with the blade of the ice making part.

Inaccessible

to kids

Clean and 
hygienic places!

 

 

 

Make sure to observe the following.

  

  

 Since the product makes use of water, proper water supply and draining facility are required.

  

 Water may leak during installation or operation for diverse reasons. 

    Thus, proper draining must be prepared.
    Since there is danger of electric shock due to moisture from leak, be sure to observe the following:
    1. When installing the product indoors, be sure to have a natural drainage facility and make
       the floor waterproof, especially if the floor may get damaged due to leak.
    2. A draining outlet must be available at the installation site; be sure to connect the drain hose.
    3. Make sure that the floor is sloped so that any leaked water gets drained away
       even if the drain hose gets dislodged or damaged. Install a water overflow prevention
       wall to prevent damage.

※ Adjust the height by turning the footing if the floor is sloped to set it stably.
※ The manufacturer will not be liable for any problem arising from failure to comply with the 
    warnings above, dislodged / damaged water supply hose, or inappropriate drain facility.

Warnning

Summary of Contents for IM-0350-AC













































Reviews: