Icegame DODGEBALL ULTIMATE ARENA Service Manual Download Page 77 | Manualshive

Page: 77 / 87

background image

77

DB3216X Leaderboard Assembly and Parts

The leaderboard assembly contains the leaderboard displays, two
WR2032X five digit displays, Multiple LED strips, WH2236X matrix
display board, 2 RB2009EX receiver sensors, 2 FP2009EX
Transmitter boards, DB3102X Blocker arm and motor assembly,
three DB2033X target boards, two ML2032X display boards, and a
DB3068X Dot Matrix Grid.

Removing the DB3068X Dot Matrix grid assembly.

4) Then from the front, remove the upper support bar.

1) Open the upper back door access panel.

2) Unplug the two ribbon cables.

(Mark the cables A and B to note where they go).

3) Disconnect the DC power cables.

«
...
75
76
77
78
79
...
»

Summary of Contents for DODGEBALL ULTIMATE ARENA
























































































Reviews:

No comments

Related manuals for DODGEBALL ULTIMATE ARENA

Brand: Bally Pages: 32

Brand: Neopost Pages: 16

Brand: Rock-Ola Pages: 19

Brand: Necta Pages: 19

Brand: SandenVendo Pages: 57

Brand: Paitec Pages: 21

Brand: Morgana Pages: 29

Slam'N'Jam Junior

Brand: LAI Games Pages: 42

Brand: LG Pages: 51

Brand: Coastal Amusements Pages: 38

Brand: Hitachi Pages: 16

Pinball Raiders

Brand: Tecway Pages: 15

Brand: Tecway Pages: 19

Brand: Tecway Pages: 27

Brand: Formax Pages: 5

Brand: Formax Pages: 10

Brand: Formax Pages: 13

Brand: Formax Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands