background image

 3

 

SAFETY AND WARNINGS BEFORE YOU BEGIN

 

WARNING: WHEN INSTALLING THIS GAME, A GROUNDED A.C. RECEPTACLE MUST BE USED. 
FAILURE TO DO SO COULD RESULT IN INJURY TO YOURSELF OR OTHERS. FAILURE TO USE A 
GROUNDED RECEPTACLE COULD ALSO CAUSE IMPROPER GAME OPERATION, OR DAMAGE TO 
THE ELECTRONICS.

 

NOTE: THIS GAME IS INTENDED FOR INDOOR USE ONLY.

 

DO NOT DEFEAT OR REMOVE THE GROUNDING PRONG ON THE POWER CORD FOR THE SAME 
REASON AS GIVEN ABOVE. USING AN IMPROPERLY GROUNDED GAME COULD VOID YOUR 
WARRANTY. 

HAVE A QUALIFIED ELECTRICIAN CHECK YOUR A.C. RECEPTACLE TO BE SURE THE GROUND 
IS FUNCTIONING PROPERLY. 

THIS GAME IS DESIGNED TO DISSIPATE STATIC ELECTRICITY THROUGH THE GROUNDING 
PLANE OF THE GAME. IF THE A.C. GROUND DOES NOT WORK, THE GAME COULD DISCHARGE 
STATIC ELECTRICITY THROUGH THE GAME CIRCUITRY, WHICH COULD CAUSE DAMAGE. 

THE POWER SUPPLY IS NOT VOLTAGE ADJUSTABLE. TO OPERATE THE GAME AT VOLTAGES 
OTHER THAN THOSE IT WAS DESIGNED FOR. PLEASE CONTACT OUR SERVICE DEPARTMENT 
FOR VOLTAGE CONVERSION INFORMATION. 

WARNING 

DO NOT remove any of the components on the main board (e.g. compact flash and eproms) 
while the game is powered on. This may cause permanent damage to the parts and the main 
board. Removing any main board component part while powered on will void the warranty. 

ALWAYS REMOVE POWER TO THE GAME, BEFORE ATTEMPTING ANY SERVICE, 

UNLESS NEEDED FOR SPECIFIC TESTING.  FAILURE TO OBSERVE THIS PRECAUTION 

COULD RESULT IN SERIOUS INJURY TO YOURSELF OR OTHERS.

 

THIS GAME IS NOT SUITABLE FOR INSTALLATION IN AN AREA WHERE A WATER JET COULD BE 
USED. 

This appliance is not intended for use by persons (including children) with reduced physical, sensory or 
mental  capabilities,  or  lack  of  experience  and  knowledge,  unless  they  have  been  given  supervision  or  
instruction concerning use of the appliance by a person responsible for their safety.  Children should be 
supervised to ensure that they do not play with the appliance. 

AC Power Information

 

The games main fuse is accessed through the back of the game at the power mod.  Above the 
power cord is a small panel that contains the main fuse.   

The value of the fuse for 120 volt users is 4 AMPS at 250Volt type slow blow. 

The value of the fuse for 220/230 volt users is 2AMPS at 220/230 Volt type Slow Blow. 

Summary of Contents for DB1200X
























































































Reviews: