background image

I

PAPER FOLDER

Important Information

- This manual is designed to help you to install, operate and maintain the Table Top
Folder PF-P280. Read, understand and keep this manual in a safe and convenient
place.

- Do not operate the PF-P280 until you read and understand the instructions in this
manual.

- Horizon International Inc. shall not be liable for incidental consequential damages
resulting from : improper or inadequate maintenance by customer; unauthorized modi-
fication or misuse; operation outside of the environmental specifications for the prod-
uct.

- No Horizon dealer and distributor is authorized to make any modification, expres-
sion, or addition to the warranties written in contract.

- Horizon International Inc. pursues a policy of continuing improvement in design and
performance of the product. Therefore, the product design and specifications are sub-
ject to change without prior notice and without our legal obligation.

- All rights are reserved. No part of the manual may be photocopied, reproduced or
translated to another language without the prior written consent of Horizon Interna-
tional Inc.

030123/PFP280/05E/NO/MM/

UM203002-05

PF-P280

Summary of Contents for PF-P280



































Reviews: