IBP HDM97 Pocket Series User Manual Download Page 16 | Manualshive

Page: 16 / 50

background image

General

12

Switching on the instrument

The instrument is switched on and off by pressing the

key.

Display test during start up

Immediately after switching on the instrument the display shows all
possible  segments  dark  for  two  seconds.  Compare  the  display  with
the picture on the right side. Do not use the instrument further if you
discover  any  missing  segment,  because  wrong  values  could  be
displayed which may lead to misreading.

The  content  of  the  display  must  be  shown  exactly  like  this  picture
right from this text.

Power saving function

The

HDM97

Pocket

switches off automatically if the battery is empty. If enabled, it also switches off after a

specified time if one of the conditions listed below becomes true for the specified time period.

•

In pressure mode: The value remains 0 for the specified time period

•

In conductivity mode: The conductivity is 0 µs/cm for the specified time period

•

In pH mode: The pH probe is not connected for the specified time period

The

HDM97

Pocket

does not switch off when one of the conditions below are met

•

A computer is connected to the meter

•

The TIMER / stopwatch is running, regardless if displayed or hidden.

Displaying battery charge progress and finish

If the battery is being charged the symbol at the left top corner in the display is animated in 4 steps. There is
a delay of one second displaying each step. After the last step has been displayed the animation starts from
again like illustrated in the picture below.



➔

➔

➔

















After the battery has been charged up to its maximum capacity, the inner 3 columns of the battery symbol
start to blink in a one second period as shown is the illustration below.



➔















«
...
14
15
16
17
18
...
»

Summary of Contents for HDM97 Pocket Series



















































Reviews:

No comments

Related manuals for HDM97 Pocket Series

Brand: Kawai Pages: 19

Brand: Calculated Industries Pages: 64

Brand: Eaton Pages: 43

Power Xpert PXM 4000

Brand: Eaton Pages: 28

Brand: Felix Instruments Pages: 102

CellaCast PA8 Series

Brand: Keller Pages: 12

Brand: Omano Pages: 14

Brand: QALCOMET Pages: 52

Brand: Vega Pages: 28

Brand: Vega Pages: 20

Brand: AEMC Pages: 4

Brand: Cecomp Pages: 4

Brand: Hilti Pages: 146

BML-S1G0-Q71 Series

Brand: Balluff Pages: 20

Brand: Scaletron Pages: 63

Brand: FASAR ELETTRONICA Pages: 2

Precision KMS7101

Brand: Kreg Pages: 16

Intelligizer Fence Monitor

Brand: Zareba Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands