IBP HDM97 Pocket Series User Manual Download Page 11 | Manualshive

Page: 11 / 50

background image

7

General

Product Details

Appliance Part

HDM97

BL

HDM97

BH

Flow

Pressure

HDM97

BN

HDM97

BO

Conductivity
Temperature

Pressure Conductivity
Temperature

HDM97

BP

HDM97

BQ

pH Pressure Conductivity
Temperature

Flow Pressure Conductivity
Temperature

HDM97

BQ with Option C (Conductivity Probe Connector)

Flow Pressure Conductivity
Temperature

Depending  on  the  configuration  the  appliance  part  consists  of  a  BNC  inlet  for  pH  electrode  connection,  a
male  connector  for  pressure  transducer  inlet,  a  connectorfor  the  flow  probe  and  a  directly  attached  cable
which leads to the conductivity / temperature probe or connector for the probe. The appliance part is isolated
against  the  USB-Connector  withstanding  4000V  AC  or  6000V  DC  for  one  minute  minimum  according  to
ISO EN 60601-1.

«
...
9
10
11
12
13
...
»

Summary of Contents for HDM97 Pocket Series



















































Reviews:

No comments

Related manuals for HDM97 Pocket Series

Brand: Valeport Pages: 25

Brand: WAGER Pages: 36

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 4

Brand: Hanna Instruments Pages: 2

Brand: Parkside Pages: 114

Brand: Dräger Pages: 538

Brand: SKF Pages: 12

Brand: ISKRAEMECO Pages: 12

RAVTD1760WS Series

Brand: Ravaglioli Pages: 24

Brand: EPE Conseil Pages: 3

Brand: Primes Pages: 48

Brand: Chauvin Arnoux Pages: 64

1101-3121-0049-800

Brand: S+S Regeltechnik Pages: 16

Brand: SEAWARD Electronic Pages: 57

Brand: Oasis Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands