IBP HDM97 Pocket Series User Manual Download Page 7 | Manualshive

Page: 7 / 50

background image

3

Delivery

Introduction

The

HDM97

Pocket

meter series are reference instrument designed for the calibration of medical devices such

as hemodialysis machines. Please read this entire manual carefully before the first use of the instrument.

Application

Depending on the version the

HDM97

Pocket

may be equipped with up to 5 acquisition channels:

Channel

HDM97BL

HDM97BH

HDM97BN

HDM97BO

HDM97BP

HDM97BQ

Conductivity









Temperature









Timer













Pressure









pH



Flow





The instrument was designed to be used as a dialysis machine maintenance instrument, but can also be used
as laboratory measuring instrument as well as instrument for environmental purposes.

This instrument displays measuring values numeric. Graphical displays are available through a PC or
Notebook using the optional Software

IBPView

.

Using the USB communication interface it is possible to obtain measuring values regardless of the
instrument display's content. These values can be displayed in any way or stored for further processing.

«
...
5
6
7
8
9
...
»

Summary of Contents for HDM97 Pocket Series



















































Reviews:

No comments

Related manuals for HDM97 Pocket Series

Brand: Yamaha Pages: 69

Brand: 3B6 Pages: 30

Brand: Eaton Pages: 43

Brand: Oceanic Pages: 152

Brand: Kaiterra Pages: 8

Brand: Kaiterra Pages: 12

Brand: Larson Davis Pages: 536

Brand: Magnum Energy Pages: 3

Kotron 805 series

Brand: Magnetrol Pages: 36

Brand: Magnescale Pages: 104

Brand: Magnescale Pages: 44

Brand: WalkLAB Pages: 16

Brand: QEED Pages: 6

Brand: Saluki Technology Pages: 161

AcuRev 1310 Series

Brand: AccuEnergy Pages: 109

Prosonic S FMU90 PROFIBUS DP

Brand: Endress+Hauser Pages: 110

Brand: EIJKELKAMP Pages: 11

Brand: K&K Sound Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands