IBM TotalStorage FAStT600 Installation And User Manual Download Page 48

Page: 48 / 134

8. Remove the white screws and nuts

from the storage server bezel; then slide

the storage server into the rack. Align the bezel locator pins and attach the
bezel with two M6 screws

; then install and tighten the 6-32 in. screws

9. Reverse step 1 through step 4 to reinstall the components that you removed.

See your storage server documentation to complete your installation. Store this
information with the storage server documentation for future use.

Setting server ID settings

The FAStT600 comes with a server ID switch that is used to identify the FAStT600
on a Fibre Channel loop. The server ID switch is located on the back of the unit, as
shown in Figure 16 on page 19.

Figure 14. Rail adjustment screws

Figure 15. Server installation

IBM TotalStorage FAStT600 Fibre Channel Storage Server: Installation and User’s Guide

Summary of Contents for TotalStorage FAStT600







































































































































Search results

Summary of Contents for TotalStorage FAStT600

Reviews:

Related manuals for TotalStorage FAStT600

Brands by name

Popular brands

IBM TotalStorage FAStT600, Installation And User Manual

Search results

Summary of Contents for TotalStorage FAStT600

Reviews:

Related manuals for TotalStorage FAStT600

Brands by name

Popular brands