IBM Power 770 Technical Overview And Introduction Download Page 95

Page: 95 / 220

Chapter 2. Architecture and technical overview

Table 2-22 summarizes the internal storage combination and the feature codes that are
required for any combination.

Table 2-22 SAS configurations summary

SAS
subsystem
configuration

FC
5662
CCIN
2BC2

External SAS
components

SAS port
cables

SAS
cables

Notes

Two-way split
backplane

None

N/A

IBM i does not support
this combination.
Connecting to an
external disk
enclosure is not
supported.

Three-way
split backplane

Dual x4 SAS
adapter
(FC 5901
CCIN 57B3)

Internal SAS
port
(FC 1815)
SAS cable
for three-way
split
backplane

AI cable
(FC 3679) -
Adapter to
internal drive
(1 meter)

IBM i does not support
this combination.
An I/O adapter can be
located in another
enclosure of the
system.

Dual storage
IOA with
internal disk

Yes

None

N/A

Internal SAS port
cable (FC 1815)
cannot be used with
this or high availability
RAID configuration.

Dual storage
IOA with
internal disk
and external
disk enclosure

Yes

Requires an
external disk
enclosure
(FC 5886)

Internal SAS
port
(FC 1819)
SAS cable
assembly for
connecting
to an
external SAS
drive
enclosure

FC 3686 or
FC 3687

1-meter cable is
FC 3686.
3-meters cable is
FC 3687.

Summary of Contents for Power 770





























































































































































































































Search results

Summary of Contents for Power 770

Reviews:

Related manuals for Power 770

Brands by name

Popular brands

IBM Power 770, Technical Overview And Introduction

Search results

Summary of Contents for Power 770

Reviews:

Related manuals for Power 770

Brands by name

Popular brands