IBM Power 770 Technical Overview And Introduction Download Page 90 | Manualshive

Page: 90 / 220

background image

76

IBM Power 770 and 780 (9117-MMD, 9179-MHD) Technical Overview and Introduction

2.8.10 Fibre Channel over Ethernet (FCoE)

FCoE allows for the convergence of Fibre Channel and Ethernet traffic onto a single
adapter and converged fabric.

Figure 2-18 compares an existing Fibre Channel and network connection, and a
FCoE connection.

Figure 2-18 Comparison between existing Fibre Channel and network connection and FCoE connection

Table 2-18 lists the available Fibre Channel over Ethernet adapter. It is a high-performance
Converged Network Adapters (CNA) using SR optics. Each port can provide network
interface card (NIC) traffic and Fibre Channel functions simultaneously.

Table 2-18 Available FCoE adapter

For more information about FCoE, see An Introduction to Fibre Channel over Ethernet, and
Fibre Channel over Convergence Enhanced Ethernet, REDP-4493.

2.8.11 InfiniBand host channel adapter

The InfiniBand architecture (IBA) is an industry-standard architecture for server I/O and
inter-server communication. It was developed by the InfiniBand Trade Association (IBTA) to
provide the levels of reliability, availability, performance, and scalability necessary for present
and future server systems with levels significantly better than can be achieved by using
bus-oriented I/O structures.

InfiniBand (IB) is an open set of interconnect standards and specifications. The main
IB specification is published by the InfiniBand Trade Association and is available at the
following location:

http://www.infinibandta.org/

Ethernet

and Fibre
Channel

Cables

Ethernet

Cable

Fibre Channel

Cable

FC Switch

Ethernet Switch

CEC or I /O Drawer

Et hernet

CEC or I /O Drawer

FC

Rack

Fibre Channel (FC)

Device or FC Switch

Ethernet

C ables

Ethernet

Cable

Fibre Channel

Cable

FCoE Switch

CEC or I/O Drawer

Rack

Fibre Channel (FC)

Device or FC Switch

FCoE

Ethernet Device/

Sw itch

Ethernet Device/

Switch or FCoE

Device/Switch

Feature
code

CCIN

Adapter description

Slot

Size

OS
support

5708

2B3B

10 Gb FCoE PCIe Dual Port adapter

PCIe

Full height
Short

AIX,
Linux

«
...
88
89
90
91
92
...
»

Summary of Contents for Power 770





























































































































































































































Reviews:

No comments

Related manuals for Power 770

Brand: Makita Pages: 3

Brand: Makita Pages: 2

Brand: Makita Pages: 3

Brand: Gallagher Pages: 39

Brand: Makita Pages: 3

Brand: Earlex Pages: 4

Brand: Keithley Pages: 160

Brand: Keithley Pages: 22

Brand: Keithley Pages: 66

Brand: Keithley Pages: 58

Brand: Laser Pages: 8

Brand: Grizzly Pages: 44

Brand: Sealey Pages: 3

Brand: Würth Pages: 8

Brand: Metabo Pages: 72

Brand: Milwaukee Pages: 35

EnergyGrind-100

Brand: PEUGEOT Pages: 10

Brand: National Instruments Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands