background image

20TONNE ECONOMY FLOOR TYPE 

HYDRAULIC PRESS

MODEL NO:

 YK20ECF.V2

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SAFETY

 

9

   Familiarise yourself with the applications, limitations and hazards of the press.

 

9

   Maintain  the

 

press in good condition (use an authorised service agent).

 

9

   Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

 

9

   Keep the press clean for best and safest performance.

 

9

   Locate the press in an adequate working area for its function, keep area clean and tidy and free from unrelated materials and ensure  

  there is adequate lighting.

 

9

   Ensure the workpiece is correctly secured before operating the press.

 

9

   Ensure that all fittings are tight before each use.

 

9

   Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain long hair.

 

9

   Keep hands and body clear of the table when operating the press.

 

9

   Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

 

9

   Keep children and unauthorised persons away from the working area.

 

9

   Securely attach the press to a flat, firm, level surface capable of supporting the weight of press and any workpiece taking into account  

  clearance for workpieces.

 

9

   When not in use, release pressure from the hydraulic unit and clean the press. Stand or store the V blocks in a safe location.

 

8

   DO NOT

 operate the press if any parts are missing as this may cause failure and/or possible personal injury.

 

8

   DO NOT

 use the press for a task it is not designed to perform.

 

8

   DO NOT

 make any modifications to the press.

 

8

   DO NOT

 exceed the rated capacity of the press.

 

8

   DO NOT

 apply off-centre loads.

 

8

   DO NOT

 allow the workpiece or the v blocks to fall from the table.

 

8

   DO NOT

 get the press wet or use in damp or wet locations or areas where there is condensation.

 

8

   DO NOT

 operate the press when you are tired or under the influence of alcohol, drugs or intoxicating medication.

 

8

   DO NOT

 climb upon the press.

 

8

   DO NOT

 use the press to compress a spring or any other item that could disengage and cause a potential hazard including personal  

 injury.

 

8

   DO NOT 

stand directly in front of a loaded press and never leave a loaded press unattended.

 

8

   DO NOT 

allow untrained persons to operate the press.

 

‰

   WARNING! 

Always wear approved eye or face protection when operating the press. A full range of personal safety equipment is  

 

  available from your Sealey stockist.

 

‰

   WARNING:  DO NOT 

top up hydraulic unit with brake fluid, or any other fluid other than a good quality hydraulic oil (Sealey Part

  

 

 

Number: HJO500MLS/HJO5LS) as this may cause serious damage to the hydraulic unit and will invalidate the warranty. 

 

‰

   WARNING! 

Always position the press against a wall. If the press is situated in the open workshop, it is essential that a guard  

 

  be placed at the rear of the unit. This will prevent injury to bystanders in the event of the work piece ejecting suddenly.

 

 

‰

   WARNING!

 The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may    

  occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this   

 

  product, but must be applied by the operator.

 

   DANGER! 

The press is top heavy. If it requires moving after assembly or for relocation, use suitable slings around the top  

 

  crossbeam, or lift direct with a forklift with the forks located under the top crossbeam. 

DO NOT

 use a pallet truck.

2.  INTRODUCTION

 

  Economy model is suitable for the serious enthusiast or occasional professional use. Made from a high quality steel with a powder   

 

  coated finish to help corrosion resistance.

YK20ECF.V2 Issue 1 19/03/21

Original Language Version

© Jack Sealey Limited

Refer to 

instructions

 Wear a face 

shield

Warning 

crushing of 

hands

Wear protective 

gloves

Wear protective 

clothing

Wear  protective  

footwear

Reviews: