National Instruments NI PXIe-4113 Calibration Procedure Download

Page: 1 / 18

CALIBRATION PROCEDURE

NI PXIe-4113

Dual-Output Programmable DC Power Supply

This document contains the verification and adjustment procedures for the NI PXIe-4113
(NI 4113). Refer to

ni.com/calibration

for more information about calibration solutions.

Contents

Voltage Output and Measurement.....................................................................................5
Current Output and Measurement.....................................................................................7
Load Regulation................................................................................................................9
Remote Sense..................................................................................................................12

Adjustment.............................................................................................................................. 13

Reverification..........................................................................................................................17
Worldwide Support and Services............................................................................................ 17

Required Software

Calibrating the NI 4113 requires you to install the following software on the calibration
system:
•

NI-DCPower 15.1 or later.

•

Supported application development environment (ADE)—LabVIEW or
LabWindows

™

/CVI

™

•

Supported operating system—Windows.

Summary of Contents for NI PXIe-4113



















Search results

Summary of Contents for NI PXIe-4113

Reviews:

Related manuals for NI PXIe-4113

Brands by name

Popular brands

National Instruments NI PXIe-4113, Calibration Procedure

Search results

Summary of Contents for NI PXIe-4113

Reviews:

Related manuals for NI PXIe-4113

Brands by name

Popular brands