IBM Power 770 Technical Overview And Introduction Download Page 53 | Manualshive

Page: 53 / 220

background image

© Copyright IBM Corp. 2013. All rights reserved.

39

Chapter 2.

Architecture and technical
overview

The IBM Power 770 offers a 4-socket CEC enclosure, populated with 3-core or 4-core
processors. A fully-configured 4-drawer system has either 48 or 64 cores,
depending on which processor is specified.

The IBM Power 780 offers the same 4-socket CEC enclosure, populated with 4-core or 8-core
processors. This architecture offers a maximum system configuration of 64 or 128
cores, depending on the processor option chosen.

This chapter provides an overview of the system architecture and its major components. The
bandwidths that are provided are theoretical maximums used for reference.

The speeds shown are at an individual component level. Multiple components and application
implementation are key to achieving the best performance.

Always do the performance sizing at the application workload environment level and evaluate
performance by using real-world performance measurements and production workloads.

2

«
...
51
52
53
54
55
...
»

Summary of Contents for Power 770





























































































































































































































Reviews:

No comments

Related manuals for Power 770

Brand: 80% Arms Pages: 12

Brand: Campbell Hausfeld Pages: 8

Brand: Gates Pages: 36

CYBERCORE 1000 PLATINUM

Brand: XPG Pages: 50

Brand: Zhaoxin Pages: 5

Silent Pro Gold RS-600-80GA-D3

Brand: Cooler Master Pages: 10

Brand: Aprimatic Pages: 2

Brand: Ryobi Pages: 13

Brand: HIKOKI Pages: 24

650 Watt ATX Power Supply

Brand: Ultra Pages: 9

Brand: Nova Electronics Pages: 2

AXMINSTER Model Engineer Series

Brand: Sieg Pages: 28

Brand: UFO Pages: 8

Brand: Powersmart Pages: 17

BOSTITCH PROFESSIONAL QuietSharp Glow EPS11HC

Brand: Stanley Pages: 2

Brand: Gude Pages: 44

ELG-150-C Series

Brand: Mean Well Pages: 12

Brand: Horizont Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands