IBM Aptiva 2140 Hardware Maintenance Service Download Page 83

Page: 83 / 212

Table

2-1 (Page 17 of 23). POST and Diagnostics and Utilities Index

for Symptoms, Messages, Error Codes, or Beeps

Symptoms, Messages, Error
Codes, or Beeps

Action/FRU

Error Codes

107 - System board, processor
update error. (A-2 system board
only)

Flash BIOS
System Board

10X - System board error or
continuous beep.

System Board

110 - System board parity error.

“Memory” on page 2-37.

DIMMs
System Board

111 - I/O channel parity error.

“Memory” on page 2-37.

I/O channel memory
System Board

114 - External ROM checksum
error.

Adapter Card
System Board

129 - Cache memory error

“Memory” on page 2-37.

For A-1 system board:
System Board
For A-2 system board:
Processor

12X - Processor error.

Run the Setup Utility; see “POST Error
Codes” on page 2-3.

Processor
System Board

13X - System board error.

Run the Setup Utility; see “POST Error
Codes” on page 2-3.

Processor
System Board

151 - Real-time clock failure

System board

161 - Low CMOS battery.

CMOS clock/battery (if less than 2.8 V dc)

Run the Setup Utility; see “POST Error
Codes” on page 2-3.

System Board

Check Procedures

2-27

Get user manuals:

See SafeManuals.com

Summary of Contents for Aptiva 2140





















































































































































































































Search results

Summary of Contents for Aptiva 2140

Reviews:

Related manuals for Aptiva 2140

Brands by name

Popular brands

IBM Aptiva 2140, Hardware Maintenance Service

Search results

Summary of Contents for Aptiva 2140

Reviews:

Related manuals for Aptiva 2140

Brands by name

Popular brands