48
Bay
Form
Factor
Height
Front
Access
Usage
Part
Number
Description
RPM Height
Bays
Supported
Max
Qty
1
133mm
(5.25in)
HH
yes
IDE CD-
ROM
IDE HDDs
1, 2
2
133mm
(5.25in)
HH
yes
open
1
19K4461
20.4GB 7200rpm ATA -100 (EIDE) HDD
7200
SL
4 ... 7
3
3
89mm
(3.5in)
SL
yes
Diskette
00N8203
30GB 7200rpm ATA -100 (EIDE) HDD
7200
SL
4 ... 7
3
4
89mm
(3.5in)
SL
yes
open
22P7157
40GB 7200rpm ATA -100 (EIDE) HDD
7200
SL
4 ... 7
3
5 ... 7
89mm
(3.5in)
SL
no
open
09N4207
60GB 7200rpm ATA -100 (EIDE) HDD
7200
SL
4 ... 7
3
1. Supports removable media devices only. Hard disk drives are not
supported.
09N4226
80GB 7200rpm ATA -100 (EIDE) HDD
7200
SL
4 ... 7
3
09N4231
120GB 7200rpm ATA -100 (EIDE) HDD
7200
SL
4 ... 7
3
Nonhot-swap Ultra160 SCSI
HDDs
2
06P5750
18.2GB 10Krpm Ultra160 SCSI SL HDD
10000
SL
4 ... 7
4
06P5751
36.4GB 10Krpm Ultra160 SCSI SL HDD
10000
SL
4 ... 7
4
06P5752
73.4GB 10Krpm Ultra160 SCSI SL HDD
10000
SL
4 ... 7
4
06P5765
18.2GB 15Krpm Ultra160 SCSI SL HDD
15000
SL
4 ... 7
4
06P5766
36.4GB 15Krpm Ultra160 SCSI SL HDD
15000
SL
4 ... 7
4
Optical Devices
Bays Supported
22P6950
16X Max RAM-Read DVD-ROM Drive
3, 4
1, 2
22P6976
40x-12x-40x Max Black CD-RW Drive
3
1, 2
External Storage Expansion
Units
5
Form Factor
35311RU
EXP300 Storage Expansion Unit
6
Rack (3U)
09N7296
EXP300 Rack-to-Tower Conversion Kit
-
1.The xSeries 200 EIDE controllers support a maximum of four IDE devices per machine including CD-ROM drives,
HDDs and IDE tape drives.
2. Mixing of internal IDE and SCSI HDDs is not supported.
3. Either replace the standard CD-ROM or install in the available media bay. An IDE cable with three connectors is
included with the optional optical drive (same cable is provided standard in the system). If installing as an additional
device, connect the cable to each optical device and the IDE connector on the system board. Configure the optional
device as a master using the preset configuration if replacing the standard device or as a slave if installed as a
redundant device.
4. Audio not supported for DVD-ROM drives. The drive provides data input/output only.
5. Not supported by the external SCSI port included in SCSI models. Select an optional SCSI controller then refer to
Appendix D: Cables - Storage Unit - Controllers to confirm the controller supports the desired External Storage
Expansion Unit and to select a supported cable. For HDD or other expansion unit options, see the specific expansion
unit section.
6. EXP300 includes a single 2M Ultra2 SCSI cable and dual hot-swap 500W redundant power supplies, each with its
own power cord. To convert an EXP300 to a tower form factor, EXP300 Rack-to-Tower Conversion Kit (P/N 09N7296) is
required.
