background image

 

Workmaster E Series Bench Assembly: 

 

 

Step 3: 

Align the workbench pedestals over the ends of the support beams and lower them down over the beam 
connector plates so that the plates are on the inside of the pedestal tubing. Align the slots in the pedestal 
support beam over the inserts in the worksurface and thread the 1/4-20 x .75 hex head bolts with the 1/4 flat 
washers into the inserts. Tighten the beam connector hardware. The frame should now be aligned on the 
worksurface to even the overhangs on the right and left sides tighten the beam attachment and the pedestal 
support hardware. NOTE: Do not over tighten the hardware that goes into the threaded inserts in the 
worksurface as this could cause the inserts to pull out of the worksurface. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 

Step 4: 

Slide the workbench leg extender into the pedestal tube making sure the plastic insert in the end of the leg 
extender is exposed. Align the threads of the leg extender with the holes in the pedestal tube and select the 
desired height of the bench. Thread the 1/4-20 x .75 hex head bolts with the 1/4 flat washers into the threaded 
holes in the leg extender and tighten. Thread the floor glide into the plastic insert of the leg extender. The floor 
glides are used to level the bench when assembly is complete and it is put into position. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

If you have ordered footrests, drawers, lower shelves or suspended cabinets for this bench please see 
pages15 thru 26

 

for assembly instructions. If not the workbench can be turned over for assembly of above the 

worksurface accessories or it can be put into place. 

 
Workmaster E Series with Pedestal Cabinet Assembly: 

Summary of Contents for Workmaster C Series




































Reviews: