HYOSUNG NH-2700CE Operator'S Manual Download Page 212

Page: 212 / 298

NH-2700CE 5. Operator Function

5- 158

5.13.2.7 TERMINAL ID

The

TERMINAL ID

function is used to edit the terminal id number of ATM.

A host will identify ATM by looking at terminal ID. Terminal ID will be included in a host message and

will be printed on the receipt.

5.13.2.8 PASSWORD SETUP (MASTER PASSWORD)

This menu enables you to change current master password as new one. To change the current

password, you should input the proper one in current password field. The factory default value of

master password is "555555".

Summary of Contents for NH-2700CE










































































































































































































































































































Search results

Summary of Contents for NH-2700CE

Reviews:

Related manuals for NH-2700CE

Brands by name

Popular brands

HYOSUNG NH-2700CE, Operator'S Manual

Search results

Summary of Contents for NH-2700CE

Reviews:

Related manuals for NH-2700CE

Brands by name

Popular brands