Hyke HK7024, Instructions And Warnings For Installation And Use

Page: 9 / 36

EN
English – 7
The control unit has 3 keys OPEN ( ), STOP ( SET ), CLOSE ( ) that can be
used both for controlling the unit during testing and for programming the avail-
able functions.
The programmable functions available are divided into 2 levels and their relative
operating status is displayed by means of the 8 LEDs (
L1 … L8 ) on the control
unit (LED lit = function active; LED off = function not active).
Use the programming keys:
OPEN ( ): – key for controlling gate opening; – selection key during pro-
gramming.
STOP/SET : key for stopping a manoeuvre; if pressed for more than 5 seconds,
it enables entry to programming mode.
CLOSE ( ): – key for controlling gate closure; – selection key during programming.
6.1 - Level one programming (ON-OFF functions)
All level 1 functions are set by default to “ OFF ” and may be modified at any
time. To check the functions see Table 3 . For the programming procedure see
Table 4 .
IMPORTANT – In the programming procedure, the maximum time interval that
can elapse between activation of one key and the next is 10 seconds. When
this time elapses, the procedure terminates automatically, memorising the
modifications made up until then.
PROGRAMMING THE CONTROL UNIT
6
TABLE 3 - First level functions
LED Function Description
L1 Automatic closure
L2 Reclose after photo
L3 Always close
L4 All standby
L5 lock/Courtesy light
L6 Pre-flash
L7 “Close” becomes “Partial open 1”
L8 “Gate open light” or
“Maintenance light”
Function ACTIVE: after an opening movement, there is a pause (equal to the programmed time) after
which the control unit automatic initiates a closure movement. The factory setting for the Pause time is 30
sec.
Function NOT ACTIVE: function is “semiautomatic” type.
Function ACTIVE: if the photocells are activated during the opening or closing manoeuvre, the pause time
is reduced to 5 seconds regardless of the programmed pause time.
With “automatic closure” disabled, if the photocells are activated during closure the “automatic closure” is
activated with the programmed “pause time”.
Function ACTIVE: in the event of a power failure, even of short duration, when power is restored the con-
trol unit detects gate open and automatically starts a closure manoeuvre, preceded by 5 seconds of pre-
flashing.
Function NOT ACTIVE: when power is restored the gate remains where it is.
Function ACTIVE: after 1 minute from the end of the manoeuvre, the control unit turns off the “BlueBus”
output (connected devices), Bus T4 (connected devices), the outputs flash, ELS and sca, some internal
circuits and all leds with the exception of the BlueBus led, which flashes at a slower interval. When the
control unit receives a command, it resumes normal operation (after a short delay). This function is used
to reduce consumption, an important aspect in the case of battery powered devices or when using pho-
tovoltaic panels.
Function ACTIVE: the “electric lock” output switches its operation to “courtesy light”.
Function NOT ACTIVE: the output operates as an electric lock.
Function ACTIVE: a 3 second pause can be added between the flashing light signal and the start of the
manoeuvre to provide advance warning of a hazard situation.
Function NOT ACTIVE: flashing light signal coincides with the start of the manoeuvre.
Function ACTIVE: all the commands corresponding to “Close” (“Close” input or “Close” radio control) are
replaced by the “Partial open 1” command.
Function ACTIVE: the “gate open light” output on the control unit switches to the “maintenance light”
function.
Function NOT ACTIVE: the output operates as “gate open light”.
TABLE 4 - Programming procedure (first level functions)
01. Press and hold down the “ Set ” key for approx. 3 seconds;
02. Release the key when LED “ L1 ” starts flashing;
03. Press the “ ” or “ ” key to move the flashing LED to the LED representing the function to be modified;
04. Press “ Set ” to change the status of the function:
(short flash = OFF; long flash = ON);
05. Wait 10 seconds (maximum time) to exit the programming mode.
Note – During this procedure, points 03 and 04 need to be repeated when programming other functions to “ON” or “OFF” during the phase itself.
SET
SET
SET
L1
or
3 s
10 s