background image

 

Unit features

 

LVU-CD-10 

en(us) 

Page 19 / 52

BeWa LVU-CD-10 Eco 4067271 en-us 2016-01-08.doc 

2016-01-08

 

Unit features 

The LowViscosity Unit LVU is intended for offline filtration. The LVU removes 
solid particle contamination and free water from diesel fuel. 
Diesel fuel is often subject to long storage periods, especially in tanks which 
may be used infrequently. As a result, solid particles and water are often 
deposited on the bottom of the tank and can then damage pumps and 
sensitive components when switching on the motor. 
In addition, over an extended period of time free water in a tank provides a 
breeding ground for diesel fuel pests (microorganisms such as bacteria, 
algae, fungus, etc.). 
Both can quickly lead to blockage of the machine filter and to damage to 
diesel injection system components. The consequence: impermissibly high 
levels of dangerous emissions from the combustion engine. This leads to 
high costs for down time, replacement parts, maintenance and repairs. 
The use of the LowViscosity Unit LVU minimizes contamination to a system 
and prevents expensive system down time. It also helps to avoid the 
necessity of early and expensive disposal of diesel fuel. 
 
The filtration unit is suitable for diesel maintenance in: 

  Tanks on mobile / stationary emergency power units 

e.g. in hospitals, shopping centers and power plants 

  Tanks of portable machines, e.g. harvesting and construction 

machinery 

  Storage tanks e.g. for agriculture and mining 

  Tanks on yachts and leisure craft 

 

Summary of Contents for LVU-CD-10





















































Reviews: