Hwasung HMK-056 User Manual Download Page 52 | Manualshive

Page: 52 / 69

background image

Model

Rev.

Page

HMK-056

Ver1.01

51

DLE+ENQ+n

[Name]

Raltime buffer clear, or reset.

[Format]

ASCII DLE

ENQ

n

Hex

10h

05h

n

Decimal 16

5

n

[Range]

n=2,3

1)n=2
[Descript]

The realtime will clear each buffer of the printer,
as soon as this command is conducted.

[Caution]                It is only valid, once the DIP SW1 is *up. *up : on.
                                If the offline is valid, and the printer receive the data same with this command,
                                The printer will be working the same with this comand. (Bit image, Data.)
                                You don’t need to be caution,once this command will be invalid if it’s online.
2)n=3
[Descript]

The realtime will reset the printer, as soon as this command is conducted.

[Range]

It is only valid, once the DIP SW1 is *up. *up : on.
The command ESC+@ will be reset.
However, it doesn’t work at the paper jam,cutting jam, has to reset compulsory.

DLE+EOT+n

[Name]

Realtime status transmission

[Format]

ASCII

DLE

EOT

n

Hex

10h

04h

n

Decimal

16

4

n

[Range]

n=2

[Descript]

The realtime send a byte of printer status, when this command is conducted.

[Caution]

It is only valid, once the DIP SW1 is *up. *up : on.

Please refer to the table of the printer status.

If the offline is valid, and the printer receive the data same with this command,

The printer will be working the same with this comand. (Bit image, Data.)

<data 1 byte of status transmission>

Bit

Status

Hex

Decimal

0

0 : Paper
1 : No paper

00h
01h

0
1

1

0 : Printer head down
1 : Printer head up

00h
02h

0
2

2

0 : Paper w/o jam
1 : Paper with jam

00h
04h

0
4

3

0 : Paper adequate
1 : Paper Near End

00h
08h

0
8

4

0 : Print complete
1 : Print or Feeding

00h
10h

0

16

5

0 : Cutter no- error (jam)
1 : Cutter error (jam)

00h
20h

0

32

6

0 (unused)

00h

0

7

0: No paper in the Support Sensor
1: Paper in the Support Sensor

00h
80h

0

128

«
...
50
51
52
53
54
...
»

Summary of Contents for HMK-056






































































Reviews:

No comments

Related manuals for HMK-056

Brand: Oki Pages: 4

Brand: 3Doodler Pages: 8

NANOCOLOR UV/VIS II

Brand: Macherey-Nagel Pages: 6

Brand: Oki Pages: 16

Brand: Olivetti Pages: 179

Brand: Olivetti Pages: 36

Brand: Oki Pages: 679

Brand: Oki Pages: 40

Brand: OKIDATA Pages: 308

Brand: OKIDATA Pages: 9

Brand: OKIDATA Pages: 2

Microline 8480 FB

Brand: Oki Pages: 12

Brand: IBM Pages: 60

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Brand: Canon Pages: 21

Brand: Canon Pages: 23

Brand: Wasp Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands