Husqvarna F2203V4 Page 141 Owner'S Manual Download

Page: 141 / 166

TROUBLESHOOTING 21

139

Faults

Possible cause

Action

Engine has too little power

Exhaust system leaky,
deformed or too little glass
fiber yarn filling in the main
silencer

–

Check exhaust system for damage.

–

Change the glass fiber yarn filling in
the main silencer.

(

p. 74)

Valve clearance too little

–

Adjust the valve clearance.

Ignition system defective

–

Ignition coil - check the secondary
winding.

–

Check the spark plug connector.

–

Check the stator winding of the alter-
nator.

The engine dies during the trip

Lack of fuel

–

Refuel. (

p. 40)

Fuse

blown

–

Change the fuses of individual electri-
cal power consumers. (

p. 111)

Fuse

blown

–

Change the fuses of individual electri-
cal power consumers. (

p. 111)

Engine overheats

Coolant level low in cooling
system

–

Check the cooling system for leaks.

–

Check the coolant level. (

p. 120)

Insufficient airflow

–

Switch off engine when stationary.

Radiator fins very dirty

–

Clean radiator fins.

Foam formation in cooling sys-
tem

–

Drain the coolant.

(

p. 120)

–

Refill with coolant.

(

p. 121)

Bent radiator hose

–

Change the radiator hose.

Thermostat defective

–

Check the thermostat.
Guideline
Opening temperature: 70 °C (158 °F)

Defect in radiator fan system

–

Check fuse

–

Check the radiator fan.

Malfunction indicator lamp
lights up or flashes

Error in the electronic fuel
injection

–

Check wiring for damage and electri-
cal plug-in connectors for corrosion
and damage.

–

Read out the fault memory using the
Husqvarna Motorcycles diagnostics
tool.

High oil consumption

Engine vent hose bent

–

Route the vent hose without bends or
replace it if necessary.

Engine oil level too high

–

Check the engine oil level. (

p. 130)

Engine oil too thin (low viscos-
ity)

–

Change the engine oil and oil filter,
clean the oil screen.

(

p. 130)

Piston and cylinder worn

–

Measure the piston/cylinder mounting
clearance.

12-V battery discharged

The 12-V battery is not being
charged by the alternator

–

Check charging voltage.

–

Check the stator winding of the alter-
nator.

Unwanted electrical power
consumer

–

Check the open-circuit current.

Combination instrument values
deleted (time, stop watch, lap
times)

The combination instrument
battery is empty

–

Change combination instrument bat-
tery. (

p. 117)

Summary of Contents for F2203V4







































































































































































Search results

Summary of Contents for F2203V4

Reviews:

Related manuals for F2203V4

Brands by name

Popular brands

Husqvarna F2203V4, Owner'S Manual

Search results

Summary of Contents for F2203V4

Reviews:

Related manuals for F2203V4

Brands by name

Popular brands