Husqvarna F2203V4 Page 119 Owner'S Manual Download

Page: 119 / 166

ELECTRICAL SYSTEM 15

117

15.11

Adjust the headlight range.

Preparatory work

–

Check the headlight setting. (

p. 116)

H03755-10

Main work

–

Loosen screw

–

Adjust the headlight range by pivoting the headlight.
Guideline

The boundary between light and dark must be exactly on
the lower mark for a motorcycle with rider (instructions on
how to apply the mark: Checking the headlight setting).

Info

A change in weight on the vehicle may require a cor-
rection of the headlight range.

–

Tighten screw

15.12

Changing the combination instrument battery

Preparatory work

–

Remove the headlight mask with the headlight. (

p. 113)

H03756-10

Main work

–

Remove screws

with the washers.

–

Pull the combination instrument upward out of the holder.

H03757-10

–

Using a coin, turn protection cap

all the way counter-

clockwise and take it off.

–

Remove combination instrument battery

–

Insert the combination instrument battery with the label fac-
ing outward.

Combination instrument battery (CR 2032) (

p. 147)

–

Check the O-ring of the protection cap for correct seating.

H03758-10

–

Position protection cap

and turn all the way clockwise

using a coin.

–

Press any button on the combination instrument.

The combination instrument is activated.

–

Position the combination instrument in the holder.

–

Mount and tighten the screws with washers.

Summary of Contents for F2203V4







































































































































































Search results

Summary of Contents for F2203V4

Reviews:

Related manuals for F2203V4

Brands by name

Popular brands

Husqvarna F2203V4, Owner'S Manual

Search results

Summary of Contents for F2203V4

Reviews:

Related manuals for F2203V4

Brands by name

Popular brands