Husqvarna F2203V4 Page 140 Owner'S Manual Download

Page: 140 / 166

21 TROUBLESHOOTING

138

Faults

Possible cause

Action

The engine cannot be cranked
(starter motor)

Operating error

–

Carry out start procedure. (

p. 36)

12-V battery discharged

–

Charge the 12-V battery.

(

p. 109)

–

Check charging voltage.

–

Check the open-circuit current.

–

Check the stator winding of the alter-
nator.

Main fuse blown

–

Change the main fuse. (

p. 110)

Starter relay defective

–

Check the starter relay.

Starter motor defective

–

Check the starter motor.

The engine turns but does not
start

Operating error

–

Carry out start procedure. (

p. 36)

Quick release coupling not
joined

–

Join quick release coupling.

Fuse

blown

–

Change the fuses of individual electri-
cal power consumers. (

p. 111)

Fuse

blown

–

Change the fuses of individual electri-
cal power consumers. (

p. 111)

Idle speed is not set correctly

–

Adjust the idle speed.

(

p. 126)

Spark plug sooty or wet

–

Clean and dry the spark plug and
spark plug connector, or change if
necessary.

Plug gap of spark plug too
wide

–

Adjust plug gap.
Guideline
Spark plug electrode gap
1.0 mm (0.039 in)

Ignition system defective

–

Check the ignition system.

Short-circuit cable in wiring
harness frayed, stop button or
emergency OFF switch faulty

–

Check the wiring harness. (visual
check)

–

Check the electrical system.

Error in the electronic fuel
injection

–

Read out the fault memory using the
Husqvarna Motorcycles diagnostics
tool.

Engine does not speed up

Error in the electronic fuel
injection

–

Read out the fault memory using the
Husqvarna Motorcycles diagnostics
tool.

Ignition system defective

–

Ignition coil - check the secondary
winding.

–

Check the spark plug connector.

–

Check the stator winding of the alter-
nator.

Engine has too little power

Air filter heavily contaminated

–

Clean the air filter and air filter box.
(

p. 69)

Fuel filter is very dirty

–

Change the fuel filter.

Fuel screen is very dirty

–

Change the fuel screen.

(

p. 129)

Error in the electronic fuel
injection

–

Read out the fault memory using the
Husqvarna Motorcycles diagnostics
tool.

Summary of Contents for F2203V4







































































































































































Search results

Summary of Contents for F2203V4

Reviews:

Related manuals for F2203V4

Brands by name

Popular brands

Husqvarna F2203V4, Owner'S Manual

Search results

Summary of Contents for F2203V4

Reviews:

Related manuals for F2203V4

Brands by name

Popular brands