Husqvarna F2203V4 Page 85 Owner'S Manual Download

Page: 85 / 166

SERVICE WORK ON THE CHASSIS 12

F03481-10

–

Check chain sliding piece for wear.
» If the lower edge of the chain pins is in line with or below

the chain sliding piece:

–

Change the chain sliding piece.

–

Check that the chain sliding piece is firmly seated.
» If the chain sliding piece is loose:

–

Tighten the screw of the chain sliding piece.
Guideline

Screw, chain slid-
ing piece

15 Nm
(11.1 lbf ft)

400985-01

–

Check the chain guide for wear.

Info

Wear can be seen on the front of the chain guide.

» If the light part of the chain guide is worn:

–

Change the chain guide.

F00322-01

–

Check that the chain guide is firmly seated.
» If the chain guide is loose:

–

Tighten the fitting on the chain guide.
Guideline

Remaining
screws, chassis

10 Nm (7.4 lbf ft)

Remaining nuts,
chassis

10 Nm (7.4 lbf ft)

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 54)

Summary of Contents for F2203V4







































































































































































Search results

Summary of Contents for F2203V4

Reviews:

Related manuals for F2203V4

Brands by name

Popular brands

Husqvarna F2203V4, Owner'S Manual

Search results

Summary of Contents for F2203V4

Reviews:

Related manuals for F2203V4

Brands by name

Popular brands