Husqvarna F2101Q1 Repair Manual Download | Manualshive

Page: 21 / 321

background image

6.9

Installing the fork legs

H01182-10

FORK, TRIPLE CLAMP 6

Main work

-

Position the fork legs.

✓ Air bleeder screw

O

of the right fork leg is positioned to

the front.

✓ Valve

f)

of the left fork leg faces the front.

Info

Grooves are milled into the side of the upper end of
the fork legs. The second milled groove (from the top)
must be flush with the upper edge of the upper triple
clamp.

The air suspension is located in the left fork leg. The
pressure and rebound damping is located in the right
fork leg.

- Tighten screws

8.

Guideline

Screw, top triple
clamp

- Tighten screws@).

Guideline

M8

Screw, bottom triple

M8

clamp

17 Nm (12.5 lbf ft)

12 Nm (8.9 lbf ft)

-

Position the brake caliper. Mount and tighten screws

C,.

Guideline

Screw, front
brake caliper

M8

25 Nm (18.4 lbf ft)

Loctite

®

243

™

-

Position the brake line and the clamp. Mount and tighten

screws

C,.

Finishing work

-

Install the front wheel. (

8

p. 119)

...

rotector

-

Remove screws

O

and take off the clamp.

-

Remove screws @ and take off the left fork protector.

-

Remove screws

(s)

and take off the right fork protector.

...

19

«
...
19
20
21
22
23
...
»

Summary of Contents for F2101Q1


































































































































































































































































































































Reviews:

No comments

Related manuals for F2101Q1

Brand: R&G Pages: 15

Brand: hepco & becker Pages: 4

Brand: Honda Pages: 3

Brand: National Cycle Pages: 5

990D0-44G00-ALM

Brand: Suzuki Pages: 24

Brand: GAS GAS Pages: 32

SCARABEO 100 4T - 06-2001 PART6

Brand: APRILIA Pages: 6

Brand: Salewa Pages: 17

Sixteenth Edition

Brand: MSF Pages: 60

Brand: Happy Trails Pages: 2

2004 Moto Matrix

Brand: Yamaha Pages: 41

Brand: Yamaha Pages: 48

Brand: Yamaha Pages: 28

2004 FJR1300(S)

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 30

Brand: Yamaha Pages: 87

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands