Husqvarna 2008 HUV4210-E Owner'S Manual Download | Manualshive

Page: 45 / 64

background image

Battery – Gasoline Vehicles

2008 Husqvarna 4210-G, 4210-E, 4210-GXP, and 4210-EXP Owner’s Manual

Page 43

ý

DANGER

- External: Flush with water. Call a physician immediately.

- Internal: Drink large quantities of milk or water followed with milk of magnesia or vegetable

oil. Call a physician immediately.

- Eyes: Flush with water for 15 minutes. Call a physician immediately.

ý

WARNING

• Do not jump start a dead battery using another battery and jumper cables.

The battery in the Husqvarna gasoline vehicle is a 12-volt, low maintenance battery that requires infrequent
watering

(Figure 25)

.

Any corrosion around the positive (+) or negative (–) terminals should be washed off with a solution of baking
soda and water (1 cup (237 mL) per gallon (3.8 L) of water). Rinse solution off the battery. Do not allow this
solution to enter battery. Be sure terminals are tight (battery terminals should be tightened to 12 ft-lb (16
N·m)). Let the terminals dry and then spray them with Battery Terminal Protector Spray (Husqvarna 603 00
00-03).

See preceding WARNING and following CAUTION.

ý

WARNING

• If battery wire terminals are damaged or corroded, replace or clean them as necessary. Failure

to do so may cause them to overheat during operation and could result in fire, property
damage, or personal injury.

Be sure battery clamp is properly tightened. Tighten to 12 ft-Ib (16 N·m). A loose battery clamp may allow the
battery to become damaged from vibration or jarring.

If battery appears weak, have it charged by a trained technician. The battery should never be left discharged
any longer than absolutely necessary (do not leave discharged overnight).

Figure 25 Battery – Gasoline Vehicle

Figure 26 Battery Electrolyte Level

1. Level Indicator 2. Cap 3. Plates
Electrolyte level at least 1/2 inch (13 MM) above plates or to
level indicator.

1

3

2

«
...
43
44
45
46
47
...
»

Summary of Contents for 2008 HUV4210-E

































































Reviews:

No comments

Related manuals for 2008 HUV4210-E

Brand: Eton America Pages: 96

Brand: Baltmotors Pages: 58

Brand: Ardisam Pages: 8

Brand: Dinli Pages: 99

PAVER SPECIAL RPS Series

Brand: Etnyre Pages: 61

Brand: gio Pages: 22

Sportsman 850 2021

Brand: Polaris Pages: 180

Brand: PAXSTER Pages: 24

Brand: MADER Pages: 115

Brand: Yamaha Pages: 405

Brand: Toro Pages: 2

Brand: GAS GAS Pages: 60

Brand: ACG Pages: 14

Brand: UTIFORM Pages: 85

Brand: Eagle Pages: 24

Brand: ADLY MOTO Pages: 39

Brand: Adly Motor Pages: 43

Brand: ADLY MOTO Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands