Husqvarna 2008 HUV4210-E Owner'S Manual Download | Manualshive

Page: 50 / 64

background image

Cleaning the Vehicle

Page 48

2008 Husqvarna 4210-G, 4210-E, 4210-GXP, and 4210-EXP Owner’s Manual

3. The fuel tank is located on passenger side of vehicle. Remove fuel cap and fill the fuel tank with fresh

unleaded gasoline only.

See preceding CAUTION.

4. Replace fuel cap on tank. Ensure cap is tightened securely.

5. Replace seat bottom.

CLEANING THE VEHICLE

Husqvarna vehicles are equipped with ABS front bodies and TPO for rear bodies. Use only commercially
available automotive cleaners with a sponge or soft cloth for normal cleaning. A garden hose at normal resi-
dential water pressure is adequate.
Husqvarna does not recommend any type of pressure washing or steam cleaning. Such a process (especially
if the vehicle has the rear body removed) will expose electrical components to moisture. Moisture entering
electrical components can result in water damage and subsequent component failure.
Use non-abrasive wax products. Battery acid, fertilizers, tars, asphalt, creosote, paint, or chewing gum should
be removed immediately to prevent possible stains.
The seats of the vehicle will last longer with proper cleaning. Use a solution of 10% liquid soap and warm
water applied with a soft cloth. For imbedded dirt, a soft bristle brush may be used. For heavy soiling, difficult
stains or scratches, blemishes, or other body damage, see Section 4 of the appropriate maintenance and ser-
vice manual.

NOTE:

Dispose of waste water properly.

Figure 32 Fuel Tank

1. Vent 2. Fuel Shut-off Valve 3. Vent Tube

1

3

2

«
...
48
49
50
51
52
...
»

Summary of Contents for 2008 HUV4210-E

































































Reviews:

No comments

Related manuals for 2008 HUV4210-E

Brand: BOMBARDIER Pages: 328

Brand: Atlanta Pages: 16

amphibious, off-road utility vehicle

Brand: Centaur Pages: 56

Brand: Fort Pages: 88

Brand: Erde Pages: 4

Stand-Up SINGLE RIDE-UP Go Series

Brand: Kendon Pages: 20

INTIMIDATOR XD 4

Brand: DFK Pages: 84

Brand: Pow’R’kraft Pages: 16

Brand: Weehoo Pages: 8

Brand: Segway Pages: 407

Abarth PB 9388A

Brand: PlayActive Pages: 10

Brand: PowerMax Pages: 110

Brand: GEM Pages: 72

Brand: GEM Pages: 85

Brand: GEM Pages: 95

Brand: GoPod Campers Pages: 14

Brand: Carry-On Trailer Corporation Pages: 44

Brand: Toro Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands