Husqvarna 2008 HUV4210-E Owner'S Manual Download

Page: 52 / 64

Vehicle Specifications

Page 50

2008 Husqvarna 4210-G, 4210-E, 4210-GXP, and 4210-EXP Owner’s Manual

VEHICLE SPECIFICATIONS

SPECIFICATIONS

Electric

HUV4210-E

Electric

HUV4210-

EXP

Gasoline

HUV4210-G

Gasoline

HUV4210-

GXP

POWER SOURCE

Drive motor:

Direct drive, 48 volts DC, shunt-wound, 3.2 hp

•

Engine:

4-cycle OHV, 286 cc, 9.5 maximum HP @3600 RPM (per SAE J 1940/1349),

single-cylinder, air-cooled, with pressure lubrication system

•

Engine:

4-cycle OHV, 351cc, 11.5 maximum HP @3600 RPM (per SAE J 1940/

1349), single-cylinder, air-cooled, with pressure lubrication system

•

Fuel system:

Side-draft carburetor with float bowl, fixed jets, fuel filters, and impulse

fuel pump

•

Governor:

Automatic ground-speed sensing, internally geared in unitized transaxle

•

Ignition:

Transistor electronic ignition with electronic RPM limiter

•

Transaxle:

Double reduction helical gear with 12.3:1 direct drive axle

•

Unitized transaxle:

Fully synchronized forward and reverse with neutral and reduced

speed reverse (11.8:1 forward, 17.1:1 reverse)

•

Torque converter:

Automatic, variable-speed, dry type

•

Electrical system:

48 volts DC, reduced speed reverse

•

Electrical system:

12 volt, 500 cca at 0 °F (-17.8 °C), 650 at 32 °F (0 °C). 105-minute

reserve capacity and 35-amp charging capacity

•

Batteries:

High capacity, deep cycle, Trojan PowerDrive 12-volt, 117 min. capacity

•

Charger:

Automatic, 48-volt; UL and CSA listed

•

STEERING/SUSPENSION/BRAKES

Steering:

Self-adjusting rack and pinion

•

Suspension:

Front and rear tapered mono-leaf springs with dual hydraulic shocks

•

Brakes:

Dual rear wheel self-adjusting brakes with cast iron drums and single brake

pedal with automatic-release park brake

•

BODY/CHASSIS

Frame/Chassis:

Twin I-Beam welded aluminum

•

Front body:

ABS

•

Rear body:

TPO

•

Tires:

20 x 10.0 – 8 tubeless, 4 ply rated

•

DIMENSIONS/WEIGHT

Overall length

100.2 inches (2545 mm)

Overall width

45 inches (1143 mm)

Overall height

(at steering wheel)

46.9 inches (1191 mm)

Wheelbase

66.5 inches (1689 mm)

Ground clearance

5.5 inches (140 mm)

Front wheel tread

34.5 in (88 cm)

Rear wheel tread

38.5 in. (98 cm)

Weight

(without batteries)

874 lb.

(396 kg)

889 lb.

(403 kg)

Weight

(dry, without battery)

781 lb.

(354 kg)

805 lb.

(365 kg)

Vehicle Specifications continued on next page...

Summary of Contents for 2008 HUV4210-E

































































Search results

Summary of Contents for 2008 HUV4210-E

Reviews:

Related manuals for 2008 HUV4210-E

Brands by name

Popular brands

Husqvarna 2008 HUV4210-E, Owner'S Manual

Search results

Summary of Contents for 2008 HUV4210-E

Reviews:

Related manuals for 2008 HUV4210-E

Brands by name

Popular brands