Husqvarna 2008 HUV4210-E Owner'S Manual Download | Manualshive

Page: 30 / 64

background image

Storage – Electric Vehicles

Page 28

2008 Husqvarna 4210-G, 4210-E, 4210-GXP, and 4210-EXP Owner’s Manual

STORAGE – ELECTRIC VEHICLES

See General Warnings on page 10.

ý

WARNING

• Turn the key switch to the OFF position, remove the key, and leave the Forward/Reverse

handle or switch in the NEUTRAL position during storage. This is to prevent unintentionally
starting the vehicle or a fire hazard. Place the Tow/Run switch in the TOW position.

• Do not attempt to charge frozen batteries or batteries with bulged cases. Discard the battery.

Frozen batteries can explode.

ý

CAUT ION

• Batteries in a low state of charge will freeze at low temperatures.
• To avoid exposing electrical components to moisture and subsequent damage, do not use

any type of pressure washing or steam cleaning equipment to wash the vehicle.

PREPARING THE ELECTRIC VEHICLE FOR EXTENDED STORAGE

1. Fully charge batteries.

See Charging Batteries on page 40.

2. Batteries should be clean and free of corrosion. Wash tops and terminals of batteries with a solution of

baking soda and water (1 cup (237 mL) baking soda per 1 gallon (3.8 L) of water). Rinse solution off bat-
teries. Do not allow this solution to enter the batteries. Be sure terminals are tight. Let the terminals dry
and then coat them with Battery Terminal Protector Spray (Husqvarna 603 00 00-03).

3. Store vehicle in a cool, dry place. This will minimize battery self-discharge.

4. Adjust tires to recommended tire pressure.

See Vehicle Specifications on page 50.

5. Perform semiannual periodic lubrication.

See Periodic Lubrication Schedules on page 35.

6. Thoroughly clean front body, rear body, seats, battery compartment, and underside of vehicle.

7. Do not engage the park brake. Chock the wheels to prevent the vehicle from rolling.

8. Keep batteries fully charged during storage.

•

Leave PowerDrive2 Chargers plugged in during storage. The onboard computer will automatically acti-
vate the charger when necessary. If charger cannot remain plugged in, or AC power will not be avail-
able during extended storage, disconnect the batteries for storage

(Figure 2, Page 12)

.

See following

CAUTION.

CAUT ION

• Be sure to check the batteries and charger monthly to maintain correct battery water level and

to ensure the charger is operating correctly during storage.

RETURNING THE STORED ELECTRIC VEHICLE TO SERVICE

1. If necessary, connect batteries and tighten terminals to 110 in-lb (12.4 N·m).

2. Fully charge batteries.

3. Adjust tires to recommended tire pressure.

See Vehicle Specifications on page 50.

4. Perform the Pre-Operation and Daily Safety Checklist on page 20.

«
...
28
29
30
31
32
...
»

Summary of Contents for 2008 HUV4210-E

































































Reviews:

No comments

Related manuals for 2008 HUV4210-E

Brand: LaTrax Pages: 36

Brand: Ardisam Pages: 8

Brand: Dinli Pages: 99

Brand: Suzuki Pages: 492

Brand: Massimo Pages: 8

Brand: Columbia Pages: 36

Express L6 - Gas

Brand: E-Z-GO Pages: 80

Brand: Landoll Pages: 80

Brand: Range Road Pages: 21

Brand: Yamaha Pages: 32

Brand: AAA Pages: 165

Multilander Logging Trailer with Utility Box

Brand: Woodland Mills Pages: 36

Brand: Woodland Mills Pages: 48

Brand: Toro Pages: 60

TrailPro Deluxe

Brand: TransTank Pages: 20

Brand: Schwinn Pages: 26

Brand: RYKOV Pages: 19

Sure-Trac ST6008

Brand: Novae Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands