Husqvarna 2008 HUV4210-E Owner'S Manual Download | Manualshive

Page: 24 / 64

background image

Driving Instructions

Page 22

2008 Husqvarna 4210-G, 4210-E, 4210-GXP, and 4210-EXP Owner’s Manual

cause resistance to rolling (moving at no more than 1 to 3 mph) (1.5 to 4.8 km/h) with the Forward/
Reverse switch in any position. When zero speed detect motor braking is engaged, the reverse buzzer
should emit a distinct pattern of beeps.

See following WARNING.

ý

WARNING

• Zero-speed detect will not limit vehicle speed to 1 mph (1.6 km/h) on very steep grades. Do

not operate vehicle on slopes exceeding 20% grades.

• Pedal Up Motor Braking (adjustable on IQ System vehicles):

Accelerate the vehicle to full speed

and then release the accelerator pedal. Motor braking should quickly and smoothly slow the vehicle to
approximately 11 mph (17.7 km/h). Motor braking will disengage when vehicle slows to 11 mph (17.7
km/h). This feature is adjustable for IQ System vehicles only. Contact your local Husqvarna dealer/dis-
tributor to inquire about this adjustable feature.

• Pedal Down Motor Braking:

Accelerate down an incline with the accelerator pedal pressed. When the

vehicle reaches maximum designed speed, motor braking should engage and limit the vehicle to its
maximum designed speed. On very steep grades, the vehicle may slightly exceed its maximum
designed speed, requiring use of the brake pedal.

Gasoline Vehicles

• Accelerator:

With the key switch in the ON position and the Forward/Reverse switch in the FOR-

WARD position, as the accelerator pedal is pressed, the engine should start and the vehicle should
accelerate smoothly to full speed. When the pedal is released it should return to the original position
and the engine should stop. All Husqvarna vehicles operate at reduced speed in reverse.

• Governor:

Check maximum speed of the vehicle. The vehicle should operate at 17 mph (27 km) on a

level surface.

DRIVING INSTRUCTIONS

ý

WARNING

• Only licensed drivers should be allowed to drive the vehicle.
• If renting or loaning the vehicle, make sure the driver is familiar with all controls and

operating procedures before allowing the vehicle to be driven.

• No more than two people should be on the vehicle at one time.
• The vehicle is not specially equipped for handicapped persons:

- Be sure all persons can properly operate the vehicle prior to allowing them to drive the

vehicle.

- Be sure all passengers are capable of securing themselves in a vehicle before allowing

them to ride in one.

• For night use, the vehicle must be equipped with headlights, taillights and reflectors.
• Stop the vehicle before shifting the Forward/Reverse handle. Failure to do so may result in

injury to an unsuspecting passenger and (or) damage to the vehicle.

• To help avoid being struck, do not stand in front of or behind the vehicle.
• Operate the vehicle from the driver seat only.

WARNING CONTINUED ON NEXT PAGE...

«
...
22
23
24
25
26
...
»

Summary of Contents for 2008 HUV4210-E

































































Reviews:

No comments

Related manuals for 2008 HUV4210-E

Brand: Irbis Pages: 99

Tanks2Go 1200lt Mobile Fuel Tank Trailer

Brand: Fuelfix Pages: 17

Brand: cectek Pages: 125

Brand: TOMCAR Pages: 106

Brand: PRONAR Pages: 166

Sportsman 9920364

Brand: Polaris Pages: 143

Brand: Racing Pages: 17

Brand: Baja Pages: 82

Brand: Range Road Pages: 10

QUAD WILD HP 300 RV - 2005

Brand: GAS GAS Pages: 72

Brand: KAYO MOTO Pages: 6

Brand: Warn Pages: 4

Sasquatch 800 UTV

Brand: Daymak Pages: 16

Brand: Verhagen Leiden Pages: 17

Brand: Truxta Pages: 24

Brand: SCORPION Pages: 32

Brand: Honda Pages: 62

Brand: Honda Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands