Husqvarna Viking Mega Quilter User Manual Download Page 25 | Manualshive

Page: 25 / 44

background image

23

Operating your MEGA QUILTER™

Balanced tension:

The ideal straight stitch has threads locked
between two layers of fabric, as shown in
the picture.

Thread tension is too tight:

If the needle thread tension is too high
the threads are interlaced above the top
fabric. Loosen the needle thread tension by
turning the dial to the left.

Thread tension is too loose:

If the needle thread tension is too low
the threads are interlaced below the lower
fabric. Tighten the needle thread tension
by turning the dial to the right.

Balancing the thread tension

The thread tension should be adjusted depending on the sewing materials, layers of
fabric and sewing method. Set the required thread tension with the thread tension dial.

«
...
23
24
25
26
27
...
»

Summary of Contents for Mega Quilter













































Reviews:

No comments

Related manuals for Mega Quilter

Brand: Fastbind Pages: 21

Brand: Blastrac Pages: 59

Brand: Foamit Pages: 10

Brand: Briteq Pages: 8

Brand: Singer Pages: 47

Brand: Singer Pages: 25

Brand: Kärcher Pages: 269

NOVAMATIC NM 2830

Brand: FUST Pages: 49

Brand: Shark Pages: 41

LK-1900B series

Brand: JUKI Pages: 174

796.3155 series

Brand: Kenmore Pages: 34

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 11

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 26

Brand: Panasonic Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands