Husqvarna Viking Mega Quilter User Manual Download Page 38 | Manualshive

Page: 38 / 44

background image

36

Maintenance and troubleshooting

The machine is noisy

• Thread has been caught in the hook race

(page 32).

• Lint has built up in the hook race or

bobbin holder (page 32).

• The machine needs oiling (page 33).

Important notes

: Before changing presser foot and needle you must turn the main

switch off. Do not attempt to sew without fabric under the presser foot.
When leaving the machine, even for only a short time, switch off the main switch.
This is important if there are any children nearby.

«
...
36
37
38
39
40
...
»

Summary of Contents for Mega Quilter













































Reviews:

No comments

Related manuals for Mega Quilter

Brand: UnionSpecial Pages: 38

Brand: JUKI Pages: 5

Brand: Babolat Pages: 28

Brand: Oki Pages: 91

artista 200 Embroidery

Brand: Bernina Pages: 43

Quilter's Cruise Control Voyager 17

Brand: Hinterberg Design Pages: 3

Brand: JUKI Pages: 2

Brand: JUKI Pages: 4

Brand: JUKI Pages: 235

Brand: JUKI Pages: 100

Brand: Koblenz Pages: 17

Brand: Philips Pages: 54

Brand: Philips Pages: 59

Brand: LAUREL Pages: 2

Brand: Laurel Metal Products Incorporated Pages: 4

SE 350 - Compact Sewing & Embroidery Combo Machine

Brand: Brother Pages: 2

Brand: Brother Pages: 6

Brand: Brother Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands