Husqvarna Viking Mega Quilter User Manual Download Page 26 | Manualshive

Page: 26 / 44

background image

24

Operating your MEGA QUILTER™

Attaching the extension table

Your MEGA QUILTER™ has been
provided with an extension table to make it
easier for you to work with large pieces of
fabric.

On the underside of the extension table
there are four table legs. Pull them all up to
support the table.

Turn the table around and slide the
extension table in the direction of the arrow
in the picture, onto the machine.

Note: There is small door on the extension table
which makes it possible for you to change the bobbin
thread without having to remove the table. You
can also store the knee lifter on the backside of the
extension table.

«
...
24
25
26
27
28
...
»

Summary of Contents for Mega Quilter













































Reviews:

No comments

Related manuals for Mega Quilter

Brand: Omron Pages: 6

FaxFinder FF240

Brand: Multitech Pages: 31

Brand: Tornado Pages: 54

Brand: GBC Pages: 74

MEMORYCRAFT 300E

Brand: Janome Pages: 48

Brand: Singer Pages: 27

Brand: Strobel Pages: 42

Brand: Radio Shack Pages: 20

Brand: GBC Pages: 2

Pro-Stitcher BLPS3

Brand: Baby Lock Pages: 105

Brand: JUKI Pages: 108

Brand: Singer Pages: 54

Brand: Canon Pages: 51

Laser Class 810

Brand: Canon Pages: 412

MultiPASS C3500

Brand: Canon Pages: 304

LASER CLASS 710

Brand: Canon Pages: 436

Brand: Panasonic Pages: 112

Brand: Panasonic Pages: 144

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands