HunterDouglas Palm Beach Polysatin Installation Operation & Maintenance Download Page 23

Page: 23 / 60

INSTALLATION

Different Heights

INCORRECT

Same Height

CORRECT

Bypass Track Systems

Step B. Install the Frame

IMPORTANT:

Tighten the mounting screws snugly, but do not overtighten.

Inside Mount

Center the frame in the opening.

Using the provided screws, attach the top of the frame to the opening and level. Use shims
as needed to ensure a level installation.

Outside Mount

Center the frame over the opening at the
desired height.

Attach the

top frame

first, starting with one

fastener at the highest corner.

IMPORTANT:

Install all mounting screws

into studs or the window header.

Place a four foot level on the top frame and
secure the second fastener in the top frame
at the other corner, ensuring the top frame
is level.

Finish attaching the top frame by securing one screw at each stud, 16" to 24" apart,
depending on the type of construction.

➤

Space screws no more than 30" apart if mounting into the header.

Step C. Attach the Tracks to the Frame

Before attaching the tracks, make sure that you have inserted the correct number of carriers
(two carriers for each panel) into the appropriate track.

Prior to inserting the carriers, check that the carrier heights are consistent from carrier to
carrier (see photos below). Adjust as necessary.

Summary of Contents for Palm Beach Polysatin





























































Search results

Summary of Contents for Palm Beach Polysatin

Reviews:

Related manuals for Palm Beach Polysatin

Brands by name

Popular brands

HunterDouglas Palm Beach Polysatin, Installation Operation & Maintenance

Search results

Summary of Contents for Palm Beach Polysatin

Reviews:

Related manuals for Palm Beach Polysatin

Brands by name

Popular brands