HunterDouglas Palm Beach Polysatin Installation Operation & Maintenance Download Page 37 | Manualshive

Page: 37 / 60

background image

INSTALLATION

35

Bay Windows

Step H. Mount the Right Bay Panel(s)

■

Repeat Step E for the right panel(s).

Step I. Rack and Secure the Right Bay Panel(s)

■

Repeat Step F for the right panel(s).

Step J. Complete the Installation

1.

To release all Duracatch

™

panel lock assemblies, insert a #2 Robertson bit into the square

hole, then push in and rotate the plunger assembly 180° counterclockwise.

2.

Close the panels and, if needed, adjust the Duracatch locks with a Robertson screwdriver as
described on page 9 so that all doors close easily yet stay firmly shut.

3.

If necessary, install magnets and strike plates (see page 41).

4.

Perform any other necessary finish work to complete the installation (see page 42).

«
...
35
36
37
38
39
...
»

Summary of Contents for Palm Beach Polysatin





























































Reviews:

No comments

Related manuals for Palm Beach Polysatin

Brand: HAMPTON BAY Pages: 11

Brand: idesk Pages: 2

Brand: ofichairs Pages: 2

Brand: Gainsborough Pages: 3

Brand: RAL Pages: 2

New Charterhouse 6028

Brand: Aspace Pages: 2

Brand: S.R.Smith Pages: 24

Brand: FUFU & GAGA Pages: 14

Brand: Castleton Home Pages: 9

MARNE 100281295-N865000016

Brand: noken Pages: 20

Brand: BABY DAN Pages: 16

Brand: Vonyx Pages: 6

Brand: Forte Pages: 32

Brand: LDI Spaces Pages: 3

INDIANA NESTING SIDE TABLE

Brand: Living & Co Pages: 9

Brand: Kings Brand Furniture Pages: 3

Brand: Astonica Pages: 2

Brand: Ameriwood HOME Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands