Hunter ACC-COM-LTE Installation Manual Download Page 3 | Manualshive

Page: 3 / 16

background image

3

Installation

Installed module

Front of Facepack

The ACC-P2P-LTE is a single-controller, point-to-point LTE module that
provides an IP data connection for computer control.
The module contains a data-only mobile phone, and requires a Hunter
account to operate.

The ACC-COM-LTE is another version of the module that includes a Site Plan,
meaning it can link to other controllers on a site with hardwire or UHF radio
communications. This requires a Hunter Site Plan account.

«
1
2
3
4
5
...
»

Summary of Contents for ACC-COM-LTE

















Reviews:

No comments

Related manuals for ACC-COM-LTE

Brand: Warren Controls Pages: 16

Brand: Laars Pages: 28

Brand: Jabra Pages: 3

Brand: jbc Pages: 44

Brand: jbc Pages: 8

Brand: Kathrein Pages: 16

Brand: Panamax Pages: 16

TruPortal TP-ADD-1DIP

Brand: Interlogix Pages: 9

Brand: Technische Alternative Pages: 68

Brand: Riello Pages: 72

Brand: C-TEC Pages: 28

Brand: Water Specialist Pages: 60

Brand: aerl Pages: 27

Brand: END ARMATUREN Pages: 32

Brand: Nice Pages: 40

Network Device NXC-8160s

Brand: ZyXEL Communications Pages: 67

Brand: VSpeak Pages: 29

Brand: Jebao Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands