Hunter Douglas Alustra Woven Textures Series Installation Operation Care Download Page 8

Page: 8 / 36

INSTALLATION

Installation Overview

To install your shade, you will need to perform the following three steps:

STEP 1:

Install the brackets and attach additional components

STEP 2:

Install the shade

STEP 3:

Connect the power source

STEP 1 — Install the Brackets

Identify the brackets for your shade.

■

Installation Brackets for Standard

Shades.

An installation bracket is placed

at each end of the standard roller shade.
There are two sizes M and L.

■

Installation Brackets for Cassette

Shades.

The number of installation

brackets required varies depending on
the shade width, as shown in the table.

■

Installation Brackets for Fascia Shades.

An installation bracket is placed at each end of the
fascia.

■

Dual Roller Brackets.

An installation bracket is placed

at each end of the dual roller shade.

Standard

Brackets

Standard

Brackets

Cassette

Installation

Bracket

Shade

Width

Brackets

Required

Up to 36"

" – 66"

" – 90"

" – 115"

Fascia

Brackets

Dual

Roller

Brackets

Summary of Contents for Alustra Woven Textures Series





































Search results

Summary of Contents for Alustra Woven Textures Series

Reviews:

Related manuals for Alustra Woven Textures Series

Brands by name

Popular brands

Hunter Douglas Alustra Woven Textures Series, Installation Operation Care

Search results

Summary of Contents for Alustra Woven Textures Series

Reviews:

Related manuals for Alustra Woven Textures Series

Brands by name

Popular brands