background image

1.0 USER INSTRUCTIONS

WARNINGS

– In case of fault and/or incorrect equipment operation, deactivate it, without making any repairs or taking any direct action.

Call your  qualified technical personnel.

– Boiler  installation  and  any  other  assistance  and/or  maintenance  activity  must  be  carried  out  by  qualified  personnel  per-

suant to AS 5601 Under no circumstances, the devices sealed by the manufacturer can be tampered with.

– It is absolutely prohibited to block the intake grilles and the aeration opening of the room where the equipment is installed.

 

– The manufacturer shall not be held liable for any damage caused by improper use of the appliance. 

– T his appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person

responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

LIGHTING AND OPERATION

BOILER IGNITION  

(fig. 23)

The first ignition of the boiler must be car-
ried out by qualified technical personnel.
Successively,  if  it  is  necessary  to  start  up
the  boiler  again,  adhere  strictly  to  the  fol-
lowing  instructions:  open  the  gas  tap  to
allow the flow of the fuel.
Move  the  main  switch  of  the  system  to
“ON”.  Af t er  a  s t op,  wait  for  about  30
seconds  before  restoring  functioning  condi-
tions do that the boiler can perform the con-
trol sequence.
If the green led is on, this indicates the pre-
sence of voltage.

Winter

Touch the key 

of the controls to activa-

te the winter mode functioning heating 

The display will be as shown as below

Summer

Press the key 

of the controls to 

de-activate  the  summer  mode.
If   the  display  is  as  shown  below  the
boiler will not operate.

Fig. 23

KEYS LOCK: 

if the device is not used, the keys will be locked 15 minutes after the last setting was made (PAR 5 by

default) and the display light switches off.
To set one of the operating modes, touch any of the keys for more than two seconds (the display will indicate one to
four segments progressively before unlocking the controls).

Page 3 of 34

Summary of Contents for sime 30e



































Reviews: