Hughes Network Systems GMH2000 Installation And Maintenance Manual Download Page 84

Page: 84 / 105

4-4 • Troubleshooting

8018653 1.1

The malfunctioning

chassis

must be replaced.

Start

Perform procedures in

section 3.1, "Activation" to

verify that appropriate

PDU power switches are set

to ON.

Has power

been restored

to chassis?

Yes

Troubleshoot

power cables.

BSC chassis is

operational.

Is -48 VDC

present?

Yes

The fan tray assembly

must be replaced.

Verify that -48 VDC is

being supplied from

the PDU to the BSC

chassis backplane.

Is -48 VDC

present?

Yes

The power distribution

unit (PDU) must be

replaced.

Are

cooling fans

operating in the

malfunctioning

chassis?

Yes

Verify that -48 VDC is

being provided at

the appropriate PDU

terminal block.

Has power

been restored

to chassis?

Yes

BSC chassis is

operational.

Install original fan tray

assembly and

replace the defective

chassis assembly.

Flowchart 4-2. No power to a single BSC chassis

Summary of Contents for GMH2000









































































































Search results

Summary of Contents for GMH2000

Reviews:

Hughes Network Systems GMH2000, Installation And Maintenance Manual, Page: 84 / 105

Search results

Summary of Contents for GMH2000

Reviews: