manualshive.com logo in svg

Hughes Network Systems GMH2000, Installation And Maintenance Manual, Page: 76 / 105

Share
Download
Hughes Network Systems GMH2000 Installation And Maintenance Manual Download Page 76

3-2 • Operation and shutdown

8018653 1.1

section “BSC module LED codes,” for descriptions of the different
module operating modes.

BSC module LED codes

Each BSC module has a front panel light-emitting diode (LED) status
display that consists of a dot LED and a seven-segment alphanumeric
LED, as shown in figure 3-1.

OK

ALM

DEBUG

S
T
A
T
U
S

RESET

RESET

DOT

LED

ALPHANUMERIC

LED

Figure 3-1. BSC module front panel LED status display

The dot LED is activated when the module is in backup (or secondary)
mode and is extinguished when module is in primary mode. When
flashing, the dot LED indicates that synchronization has been lost
between the BSC and BTS components.

The alphanumeric LED displays information regarding the switch state
of the module and its operational state. When the switch state is set to
switched-in mode (that is, the module is the primary and can receive and
transmit data) the operational state is displayed in capital letters. When
the switch state is set to switched-out mode (that is, the module is a
backup and receives data but does not transmit), the operational state is
displayed in small letters. The switch state and operational state display
codes are shown in table 3-2.

Summary of Contents for GMH2000










































































































Reviews:

No comments