manualshive.com logo in svg

Hughes Network Systems GMH2000, Installation And Maintenance Manual, Page: 57 / 105

Share
Download
Hughes Network Systems GMH2000 Installation And Maintenance Manual Download Page 57

8018653 1.1

Installing BSC hardware • 2-35

Table 2-6. Trunk cable J86, T1 FWD listing by cable connector pin number (Cont.)

Trunk

Number

Module

Slot/Port

Backplane

Signal Name

Backplane

Conn#.Pin#

Wire Color Code

Solid/Stripe

T1-00

1/0

FWD RING 00

J86.01

White/Blue

FWD TIP 00

J86.02

Blue/White

T1-01

1/1

FWD RING 01

J86.03

White/Orange

FWD TIP 01

J86.04

Orange/White

T1-02

2/0

FWD RING 02

J86.05

White/Green

FWD TIP 02

J86.06

Green/White

T1-03

2/1

FWD RING 03

J86.07

White/Brown

FWD TIP 03

J86.08

Brown/White

T1-04

3/0

FWD RING 04

J86.09

White/Gray (Slate)

FWD TIP 04

J86.10

Gray (Slate)/White

T1-05

3/1

FWD RING 05

J86.11

Red/Blue

FWD TIP 05

J86.12

Blue/Red

T1-06

4/0

FWD RING 06

J86.13

Red/Orange

FWD TIP 06

J86.14

Orange/Red

Shield/Drain wire

J86.15

Bare Wire

T1-07

4/1

FWD RING 07

J86.16

Red/Green

FWD TIP 07

J86.17

Green/Red

Future Expansion

5/0

FWD RING 08

J86.18

Red/Brown

T1-08

FWD TIP 08

J86.19

Brown/Red

Future Expansion

5/1

FWD RING 09

J86.20

Red/Gray (Slate)

T1-09

FWD TIP 09

J86.21

Gray (Slate)/Red

Future Expansion

6/0

FWD RING 10

J86.22

Black/Blue

T1-10

FWD TIP 10

J86.23

Blue/Black

Future Expansion

6/1

FWD RING 11

J86.24

Black/Orange

T1-11

FWD TIP 11

J86.25

Orange/Black

Future Expansion

7/0

FWD RING 12

J86.26

Black/Green

T1-12

FWD TIP 12

J86.27

Green/Black

Future Expansion

7/1

FWD RING 13

J86.28

Black/Brown

T1-13

FWD TIP 13

J86.29

Brown/Black

Summary of Contents for GMH2000










































































































Reviews:

No comments