Huawei UPS2000-G-6KRTLL User Manual Download Page 51

Page: 51 / 102

Name

Display

Description

Operating mode

Normal mode (default):

When the mains is

available, the UPS

works in normal mode.

If the mains frequency

is unstable, the UPS

works in inverter mode.

Auto mode: When the

mains is available, the

UPS works in normal

mode. If the mains

frequency is unstable,

the UPS works in

bypass mode.

ECO mode: When the

mains is available, the

UPS works in ECO

mode.

Battery discharge

test

Disable battery

discharge test (default).

Enable battery

discharge test. The

battery discharge test

time is controlled by

the battery discharge

time and SOC

percentage.

UPS2000-G-6KRTLL

User Manual

4 Control Panel

Issue 01 (2020-08-06)

Summary of Contents for UPS2000-G-6KRTLL







































































































Search results

Summary of Contents for UPS2000-G-6KRTLL

Reviews:

Related manuals for UPS2000-G-6KRTLL

Brands by name

Popular brands

Huawei UPS2000-G-6KRTLL, User Manual

Search results

Summary of Contents for UPS2000-G-6KRTLL

Reviews:

Related manuals for UPS2000-G-6KRTLL

Brands by name

Popular brands