Huawei UPS2000-G-6KRTLL User Manual Download Page 69

Page: 69 / 102

Alarm

Name

Severity

Clearance

Condition

Trigger

Condition

Impact on the

System

Suggestion

Lithium

battery

high

temperat

ure

protectio

Minor

The cell

temperat

ure drops

below the

protection

threshold.

● Charge

high

temperatu

protection

: The

maximum

cell

temperatu

re is

greater

than 60°C.

● Discharge

high

temperatu

protection

: The

maximum

cell

temperatu

re is

greater

than 65°C.

The internal

switch circuit of

the lithium

battery is

disconnected,

and the battery

cannot be

charged or

discharged.

Possible cause: The

ambient

temperature of the

lithium battery is

too high. There are

abnormal heat

sources around the

lithium battery.
Measure: If the

lithium battery

cannot be

recovered due to

protection against

abnormality,

contact local

Huawei engineers

to rectify the fault.

Lithium

battery

low

temperat

ure

protectio

Minor

The cell

temperat

ure rises

above the

protection

threshold.

● Charge

low

temperatu

protection

: The

minimum

cell

temperatu

re is less

than 0°C.

● Discharge

low

temperatu

protection

: The

minimum

cell

temperatu

re is less

than –

20°C.

The internal

switch circuit of

the lithium

battery is

disconnected,

and the battery

cannot be

charged or

discharged.

Possible cause: The

ambient

temperature of the

lithium battery is

too low. The heater

cannot work

properly.
Measure: If the

lithium battery

cannot be

recovered due to

protection against

abnormality,

contact local

Huawei engineers

to rectify the fault.

UPS2000-G-6KRTLL

User Manual

4 Control Panel

Issue 01 (2020-08-06)

Summary of Contents for UPS2000-G-6KRTLL







































































































Search results

Summary of Contents for UPS2000-G-6KRTLL

Reviews:

Related manuals for UPS2000-G-6KRTLL

Brands by name

Popular brands

Huawei UPS2000-G-6KRTLL, User Manual

Search results

Summary of Contents for UPS2000-G-6KRTLL

Reviews:

Related manuals for UPS2000-G-6KRTLL

Brands by name

Popular brands