Huawei UPS2000-G-3 kVA User Manual Download Page 54

Page: 54 / 90

UPS2000-G-3 kVA
User Manual (CTC)

5 Operations

Issue 02 (2019-05-05)



Set

Voltage level

and

Frequency level

based on the rated voltage and frequency. In the

case of single-phase output, set

Voltage level

to 100 V (default), 110 V, or 120 V.



Battery parameters are configurable in non-battery mode or non-battery ECO mode.



Set

Battery capacity

to the total capacity of all batteries actually connected. The value

ranges from 100 Ah to 1000 Ah. The default value is 100 Ah.



The preset password is

000001

, used to enter the

Settings

menu.



The default feature code is

999999

, used to restore the preset password.

5.2.1 Starting the UPS in Normal Mode

Procedure

Step 1

Press and hold the MANUAL ON/OFF button on each lithium battery for at least 5s and less
than 15s to activate the lithium battery.

Step 2

Close the upstream AC input circuit breaker for the UPS based on site requirements.

The initialization screen is displayed.

Step 3

The UPS enters bypass mode. When the initialization is complete, perform the following
operations:



Initial startup

On the

Settings wizard

screen, set the language (the preset language is English), system

parameters, and battery parameters. Press

. The standby screen is displayed.

Figure 5-1

Settings wizard



Non-initial startup

When the initialization is complete, the standby screen is displayed. On the standby

screen, press

to enter the main menu. Choose

Main Menu

Settings

System

Parameters

Output

to view output settings.

Step 4

Choose

Settings > Battery Parameters

, and set the

Input power limiting

based on the

actual situation.

Summary of Contents for UPS2000-G-3 kVA



























































































Search results

Summary of Contents for UPS2000-G-3 kVA

Reviews:

Related manuals for UPS2000-G-3 kVA

Brands by name

Popular brands

Huawei UPS2000-G-3 kVA, User Manual

Search results

Summary of Contents for UPS2000-G-3 kVA

Reviews:

Related manuals for UPS2000-G-3 kVA

Brands by name

Popular brands